Model NO.
KSZ-1.5S
Air Volume
3000 ± 100 M³ / H
Air Flow of Treatment
1500m³/H
Motor Power
1.5kw
Voltage
380V/50Hz or 220V/60Hz
Filter Area
10m³
Filter Cartridge
1PC
Cleaning Way
Automatic Cleaning
Maximum Pressue
2800PA
Compressed Air
0.5~0.6MPa
Noise Level
≤72±5dB
Dimension
700*800*1600mm
Weight
210±5kgs
Transport Package
Wooden Case
Specification
700*800*1600mm
Trademark
Kaisen
Origin
Shanghai, China
HS Code
8421399090
Production Capacity
200sets/Month
Certification:
CE, ISO, Polyester+PTFE
Installation Method:
Vertical
Operation Type:
Automatic
Medium Material:
Polyester+PTFE
Dust Collecting Method:
Dry
Type:
Filter Cartridge Dust Collector
KSZ-1.5S Smart Cleaning Industrial MIG And Co2 Gas Sheild Arc Welding Fume Eliminator
Working principle
Cleaning: when dusts accumulate continuously on filter cartridge's layer surface, the pressure difference between it's interior and exterior will increase steadily, when the pressure difference reach pre-set value(1000-1500Pa), the pulse valve will open, dry, oil-free compressed air rush into the reverse blow cleaning system. The system rotate and high pressure air stream jet at the interior of filter cartridge, blow off dusts accumulated on the filter cartridge's layer surface, dusts fall into dust collector under gravity, thus the whole cartridge's layer surface is cleaned.
Product introduction
1. The air purifier applies to all kinds of soot purifications caused by welding, grinding, as well as recycling of rare metals, precious materials, etc
2. For the potential of fire and molten slag particles, three protective measures are used inside purifier, to make it a longer life, more secure and reliable.
3. Intelligent model using PLC automatic control makes operation easy; filter rotates with the use of full-automatic cleaning in all directions, so that there is a more thorough cleaning filter surface, always to guarantee a constant air volume absorption; Filter is made of imported microporous PTFE film , filtering with high precision can meet GB indoor emission standards.
4. Power phase sequence instructions, short-circuit protection for lack of phase, with shutdown protection measures when too high temperature.
5. With large air volume, low noise and better capture effect. Suction hose uses the real anti-temperature, wear- resistant compounded materials, without crack and damage for sparks but longer life.
6. Photoelectric switch, efficient and energy-saving, with lighting fixtures cantilever cover (optional).
2. PTFE coating(highly effective glass fiber)micro particle filtration, filtration efficiency reaches 99.99%, meanwhile maintain a high air flow
3. purifying dry, oil-free, non-corrosive fume mixture generated in cutting and welding, collecting rare metals and valuable materials
Technical parameters
Exhibition
Company profile
Working principle
Cleaning: when dusts accumulate continuously on filter cartridge's layer surface, the pressure difference between it's interior and exterior will increase steadily, when the pressure difference reach pre-set value(1000-1500Pa), the pulse valve will open, dry, oil-free compressed air rush into the reverse blow cleaning system. The system rotate and high pressure air stream jet at the interior of filter cartridge, blow off dusts accumulated on the filter cartridge's layer surface, dusts fall into dust collector under gravity, thus the whole cartridge's layer surface is cleaned.
Product introduction
1. The air purifier applies to all kinds of soot purifications caused by welding, grinding, as well as recycling of rare metals, precious materials, etc
2. For the potential of fire and molten slag particles, three protective measures are used inside purifier, to make it a longer life, more secure and reliable.
3. Intelligent model using PLC automatic control makes operation easy; filter rotates with the use of full-automatic cleaning in all directions, so that there is a more thorough cleaning filter surface, always to guarantee a constant air volume absorption; Filter is made of imported microporous PTFE film , filtering with high precision can meet GB indoor emission standards.
4. Power phase sequence instructions, short-circuit protection for lack of phase, with shutdown protection measures when too high temperature.
5. With large air volume, low noise and better capture effect. Suction hose uses the real anti-temperature, wear- resistant compounded materials, without crack and damage for sparks but longer life.
6. Photoelectric switch, efficient and energy-saving, with lighting fixtures cantilever cover (optional).
Main feature
1. Suction arm can be rotated 360° horizontally, according to actual working condition, suction volume can be adjusted by adjusting volume valve in suction hood.2. PTFE coating(highly effective glass fiber)micro particle filtration, filtration efficiency reaches 99.99%, meanwhile maintain a high air flow
3. purifying dry, oil-free, non-corrosive fume mixture generated in cutting and welding, collecting rare metals and valuable materials
Technical parameters
| No | item | parameter |
| 1 | fan type | KSZ-1.5S |
| 2 | treatment of air flow | 1500m3/h |
| 3 | motor power | 1.5kw |
| 4 | power supply | 380V/50Hz or 220V/60Hz |
| 5 | filtration area | 10m² |
| 6 | number of filter cartridges | 1pieces |
| 7 | filter medium | Polyester+PTFE |
| 8 | filtration efficiency | >99.9% |
| 10 | compressed air | 0.5~0.6 MPa |
| 11 | maximum pressue | 2800Pa |
| 12 | noise | 72±5dB(A) |
| 13 | weight | 210±5KGS |
| 14 | dimensions(excluding suction arm) | 700×800×1600mm |
Company profile
Send Message
