DFAC 2t Water Fire Engine Fighting Truck (CB10/20 Fire Pump >48m), Fire Truck, Fire Engine

4x4 Water Tanker Fire Truck  Mounted with Fire Pumper LHD.RHD  
  DFAC 2t Water Fire Engine Fighting Truck ( CB10/20 Fire Pump >48m)

1, Chassis

Model: eq1090gj12d

Drive type: 4 × 2

Wheelbase: 4400 mm

Maximum speed: 95km / h

Engine model: cy4102-c3b (National III) (diesel)

Power: 100kW (2500r / min)

Dimension: l × w × H = 7420mmx2300mmx3000mm

Total weight: 9400kg

2, Driving room

Structure: flat head, four door double row cab

Seating: 2 in the front row (including the driver) and 4 in the back row

Equipment: in addition to the original vehicle equipment, it is equipped with 100W alarm, rotary alarm switch, power take-off control switch and indicator light.

3, Container

Capacity: water 3050kg

Material: high quality carbon steel plate, high-tech anti-corrosion treatment

Structure: welded steel plate with longitudinal and transverse anti sway plates

Equipment: 1 manhole with quick locking and opening device

1 overflow device

1 level indicator

One drain outlet, controlled by manual valve

Technical requirements: comply with ga39.4-92

4, Fire pump and piping system

Model: CB10 / 30

Flow rate: 30L / S

Pressure: 1.0MPa

Diversion time: ≤ 35S

Installation form: rear mounted



Piping system

External water inlet pipeline: there is an external water inlet at the back of the pump, with a diameter of Φ 100 mm, connected with external suction pipe and pipe teeth

Interface (sealed with a blind cover); suction pipe Φ 100 × 2m (4 pieces).

Internal water inlet pipe: one Φ 100 mm rear water inlet, which enters into the fire pump from the tank, and one Φ 100 mm rear water inlet pipe is installed

Butterfly valve, connecting liquid tank and water pump.

Outlet pipeline: * there are two normal pressure outlets controlled by Φ 80mm ball valves on both sides of the pump;

One Φ 80mm gun pipe with Φ 80mm flexible joint and Φ 80mm

Ball valve control.

Water injection pipeline: * one Φ 50mm internal water injection pipeline, which can directly inject water into the tank through the water pump;

There are one Φ 80mm external water injection nozzle on both sides of the car body.

Residual water discharge pipeline: in order to protect the water pump and ball valves, a residual water discharge valve is installed at the lowest part of the pipeline.

Cooling water pipeline: in order to make the power take-off cope with various complicated situations, it is equipped with cooling water pipeline and stainless steel ball valve.

5, Power take off

Model: full power take off

Operation: solenoid valve control, power take-off indicator light and switch are installed on the cab instrument panel

Lubrication mode: splash lubrication

6, Fire monitor

Model: PS30

Flow rate: 30L / S

Range: water ≥ 45m

Pressure: 1.0MPa

Rotation angle: horizontal 360 ° and pitch - 12 ° to 60 °

7, Equipment box and pump room

Material: the skeleton is made of high-quality steel; the mask is made of aluminum alloy plate bonded structure.

Structure: the partition in the equipment box adopts the steel structure, which is firm and reliable, and improves the space utilization rate and variability.

Open the door: there are aluminum alloy rolling shutter doors on the left and right sides of the equipment box, which are light, reliable and low noise.



Equipment layout principle

Design equipment integration according to combat formation and combat deployment;

To design all kinds of equipment brackets according to the principle of ergonomics;

The equipment is placed according to the logical relationship and frequency of use;

To stand on the ground or pedal and use any equipment within 2 movements.

Equipment layout features

It can be equipped with aluminum alloy drawer, horizontal rotating supporting plate, vertical bracket of turnover equipment, so that all kinds of equipment can be placed reasonably, and the space utilization rate is more than 80%.

The equipment in the equipment list shall be fixed with special fixtures for rust proof, vibration proof, falling off proof and scratch proof.

8, Flip the pedal

Material: high quality Q235A steel; the skin is aluminum alloy plate (anodized).

Structure: double locking with gas spring and door stop, safe and reliable.

9, Electrical system

License lamp holder: meet the requirements of gb4785, meet the needs of license lighting.

Top of the cab: equipped with a long row of luxury red and blue alarm lights, the power of the alarm is 100W; the power of the alarm is 100W

The lamp and flash lamp circuits are independent additional circuits, and the controller is installed in the cab.

Safety sign lamp: four sign lamps are installed on both sides of the lower part, one turn signal lamp is installed on both sides, and the front and rear position indicating lamps are equipped.

Ceiling lamp: installed in the equipment box and pump room, and in accordance with gb4785.

10, General technical requirements

1. All operation switches, instruments, equipment racks and vehicles shall be provided with nameplates in accordance with the specifications;

2. The performance of the whole vehicle conforms to gb7956 performance requirements and test methods for fire engines;

3. The quality of liquid tank meets the requirements of ga39.4-92;

4. The appearance of the whole vehicle is beautiful and elegant, and the flatness meets the requirements of ga39.4-92;

5. All the bonding is smooth and firm, in line with the enterprise standard.

6. All welding shall be firm and polished after welding.