MEVS-200
Magnetic Displacement Sensor
Digital Type
Angular Displacement
Integration
Metal
1.0G
IP65
Yuanben
China
Product Description
Description
Yuanben has developed a magnetic speed sensor with digital frequency output proportional to speed. The internal amplifier convert a sine wave signal output to produce a constant amplitude, digital square wave, logic-level output, robust signal-to-noise ratio, usable at lower RMPs and greater air gap between the sensor and the actuator. The pole type has flush, sealed flush, extended and sealed extended that can be selected. All models are also available with an internal temperature probe ( pt100 or NTC 10KOhm sensor), custom can select it.
Specifications
Vs, Supply Voltage: 7.5(12) to 30 VDC regulated
3.6 VDC min., unregulated
Is, Supply Current: ≤ 2 mA @ 5 VDC
≤ 4 mA @ 12 VDC
≤ 10 mA @ 24 VDC
≤ 20 mA @ 30 VDC (OC)
Vo, Signal Out: @≤ 20 mA sink, or digital square wave , TTL
Input Sensitivity: 30, 12, or 5 mVpp
Operating Freq.: ≥3 to 15 kHz
≥30 kHz at increased signal level, varies with target size, distance and pickup sensitivity. (Options: ≤ 100 kHz)
Rise/Fall Time:
Temperature: 2TE: -40°to 248 ºF(-40°to 120ºC)
Range: 3TE: -49°to 284 ºF(-45°to 140ºC)
RTD: -49°to 284 ºF(-45°to 140ºC)
NTC: -40°to 248 ºF(-40°to 120ºC)
Magnetization: Standard: ≥900 Gauss
Low Mag: 250 Gauss, TYP
Pole Piece: Flush (FP), Sealed Flush (FPS), Extended (EP), Sealed Extended (EPS), & Chisel Point (CP) Poles are available. (CP must be oriented parallel with gear tooth.)
Connectors/Pins: See page 2 for Configurations
All have gold plated contacts
Lead Wire: See page 2 for Wire & Cable Options
Assignments: Red: Supply (+)
Black: Common (-)
Green/White: Signal
Bare: Cable Shielding
Construction: SUS303 stainless steel housing Solid epoxy encapsulation
CE-Compliance: EN55011, EN50022-2
Application: Flowmeter measurement, transmission and wheel speed.
Target: Ferrous material Gear tooth with range of min 4 to 32 gear pitch. P=(N+2)/OD
P: Gear pitch, N: Num. of tooth, OD; outside Diameter
Gear Pitch & air-gap
OPTIONS: Custom configurations, thread sizes, special materials, temperature probes (NTC10, RTD100, or others), please contact us.
Surface Speed (IPS) = RPM x Outside Dia. (in.) x π/60
Yuanben has developed a magnetic speed sensor with digital frequency output proportional to speed. The internal amplifier convert a sine wave signal output to produce a constant amplitude, digital square wave, logic-level output, robust signal-to-noise ratio, usable at lower RMPs and greater air gap between the sensor and the actuator. The pole type has flush, sealed flush, extended and sealed extended that can be selected. All models are also available with an internal temperature probe ( pt100 or NTC 10KOhm sensor), custom can select it.
Specifications
Vs, Supply Voltage: 7.5(12) to 30 VDC regulated
3.6 VDC min., unregulated
Is, Supply Current: ≤ 2 mA @ 5 VDC
≤ 4 mA @ 12 VDC
≤ 10 mA @ 24 VDC
≤ 20 mA @ 30 VDC (OC)
Vo, Signal Out: @≤ 20 mA sink, or digital square wave , TTL
Input Sensitivity: 30, 12, or 5 mVpp
Operating Freq.: ≥3 to 15 kHz
≥30 kHz at increased signal level, varies with target size, distance and pickup sensitivity. (Options: ≤ 100 kHz)
Rise/Fall Time:
Temperature: 2TE: -40°to 248 ºF(-40°to 120ºC)
Range: 3TE: -49°to 284 ºF(-45°to 140ºC)
RTD: -49°to 284 ºF(-45°to 140ºC)
NTC: -40°to 248 ºF(-40°to 120ºC)
Magnetization: Standard: ≥900 Gauss
Low Mag: 250 Gauss, TYP
Pole Piece: Flush (FP), Sealed Flush (FPS), Extended (EP), Sealed Extended (EPS), & Chisel Point (CP) Poles are available. (CP must be oriented parallel with gear tooth.)
| Gear Pitch | Pole Type |
| ≤ 36 DP (MODULE 0.7) | EP62,CP10 |
| ≤ 26 DP (MODULE 0.98) | EP93 |
| ≤ 24 DP (MODULE 1.06) | EP130,FPS130, EP106,EPS106, EP125,CP45 |
| ≤ 12 DP (MODULE 2.11) | EP188 |
| ≤ 5 DP (MODULE 5.1) | EP250 |
All have gold plated contacts
Lead Wire: See page 2 for Wire & Cable Options
Assignments: Red: Supply (+)
Black: Common (-)
Green/White: Signal
Bare: Cable Shielding
Construction: SUS303 stainless steel housing Solid epoxy encapsulation
CE-Compliance: EN55011, EN50022-2
Application: Flowmeter measurement, transmission and wheel speed.
Target: Ferrous material Gear tooth with range of min 4 to 32 gear pitch. P=(N+2)/OD
P: Gear pitch, N: Num. of tooth, OD; outside Diameter
Gear Pitch & air-gap
OPTIONS: Custom configurations, thread sizes, special materials, temperature probes (NTC10, RTD100, or others), please contact us.
| Model | Pole Diameter | Output | Thread length | Cable length and Terminal | Mounting Thread | Sensor dimension |
| MEVS-200 | ¢3.3 Flush ¢2.7×0.5 extended ¢4.75×0.5 ¢3.2×1.8 ¢3.3Flush sealed SS face | 0-10 V NPN 0-5 V NPN 0-Vs, NPN 0-Vs, NPN open collector 0-Vs, NPN/PNP | 36 mm 45 mm 76 mm 89 mm 102mm 127mm 152mm | 3pin MS 3106 3pin Marco-c 3pin MS 3102 4pin Bayonet 6pin Bayonet | 5/8"-18 UNF 3/4"-16UNF M 16×1.5 M 16×1.5 | |
| ¢3.3 Flush ¢2.7×0.5 ¢4.75×0.5 ¢3.2×1.8 ¢3.3 Flush Sealed | 0-10 V NPN 0-5 V NPN 0-Vs, NPN 0-Vs, NPN open Collector 0-Vs, NPN/PNP | 30mm 45 mm 76mm 101mm 127mm 152mm | 500 single lead 1000 shield cable 2000 shield cable | 5/8"-18 UNF 3/4"-16UNF M 16×1.5 M 16×1.5 | ||
| ¢3.3 Flush ¢2.7×0.5 ¢4.75×0.5 ¢3.2×1.8 ¢3.3 Flush Sealed | 0-10 V NPN 0-5 V NPN 0-Vs, NPN 0-Vs, NPN open Collector 0-Vs, NPN/PNP | 30mm 45 mm 76mm 101mm 127mm 152mm | 500 single lead 1000 shield cable 2000 shield cable | 5/8"-18 UNF 3/4"-16UNF M 16×1.5 M 16×1.5 | ||
| ¢3.3 Flush ¢2.7×0.5 ¢4.75×0.5 ¢3.2×1.8 ¢3.3 Flush Sealed | 0-10 V NPN 0-5 V NPN 0-Vs, NPN 0-Vs, NPN open Collector 0-Vs, NPN/PNP | 33 51 | 500 single lead 1000 shield cable 2000 shield cable | 5/8"-18 UNF + 1/2-14 NPT | ||
| ¢3.3 Flush ¢2.7×0.5 ¢4.75×0.5 ¢3.2×1.8 ¢3.3 Flush sealed | 0-10 V NPN 0-5 V NPN 0-Vs, NPN 0-Vs, NPN open Collector 0-Vs, NPN/PNP | 51 71 102 | 500 single lead 1000 shield cable 2000 shield cable | 5/8"-18 UNF + 1/2-14 FNPT |
| THEAD LENGTH (A) | CASE LENGTH (B) | OUTPUT (VOLTS) | RESISTANCE (OHMS) | SPEED (IPS) | LOAD (OHMS) | INDUCTA NCE | AIR GAP | TEST GEAR | POLE TIP (P) |
| 1.12 | 2.25 | 200 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | .106 |
| 2.50 | 3.50 | 200 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | .106 |
| 3.00 | 4.00 | 200 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | .106 |
| 4.00 | 5.00 | 200 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | .106 |
| 5.00 | 6.00 | 200 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | .106 |
| 1.12 | 2.25 | 190 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | .125 |
| 2.12 | 2.72 | 190 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | .125 |
| 3.00 | 3.50 | 190 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | .125 |
| 4.00 | 4.50 | 190 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | .125 |
| 5.00 | 6.50 | 190 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | .125 |
| 1.12 | 2.25 | 150 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | .125 |
| 2.12 | 2.72 | 150 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | .125 |
| 3.00 | 3.50 | 150 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | .125 |
| 4.00 | 4.50 | 150 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | .125 |
| 5.00 | 6.50 | 150 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | .125 |
| 1.12 | 2.25 | 100 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | .125 |
| 2.12 | 2.72 | 100 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | .125 |
| 3.00 | 3.50 | 100 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | .125 |
| 4.00 | 4.50 | 100 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | .125 |
| 5.00 | 6.50 | 100 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | .125 |
| 1.12 | 2.25 | 50 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | BLIND |
| 2.12 | 2.72 | 50 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | BLIND |
| 3.00 | 3.50 | 50 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | BLIND |
| 4.00 | 4.50 | 50 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | BLIND |
| 5.00 | 6.50 | 50 P-P | 1200 | 1000 | 100K | 400 mH | .005 | 20 PITCH, 60 TEETH | BLIND |
| 1.12 | 2.25 | 1-30 P-P | 40-85 | 1000 | 100K | 25mH | .030 | 20 PITCH, 60 TEETH | .125 |
| 2.12 | 2.72 | 1-30 P-P | 40-85 | 1000 | 100K | 25mH | .030 | 20 PITCH, 60 TEETH | .125 |
| 3.00 | 3.50 | 1-30 P-P | 40-85 | 1000 | 100K | 25mH | .030 | 20 PITCH, 60 TEETH | .125 |
| 4.00 | 4.50 | 1-30 P-P | 40-85 | 1000 | 100K | 25mH | .030 | 20 PITCH, 60 TEETH | .125 |
| 5.00 | 6.50 | 1-30 P-P | 40-85 | 1000 | 100K | 25mH | .030 | 20 PITCH, 60 TEETH | .125 |
| 1.12 | 2.25 | 3.6 P-P | 250 | 280 | 100K | 100mH | .025 | 20 PITCH, 60 TEETH | .106 |
| 2.12 | 2.72 | 3.6 P-P | 250 | 280 | 100K | 100mH | .025 | 20 PITCH, 60 TEETH | .106 |
| 3.00 | 3.50 | 3.6 P-P | 250 | 280 | 100K | 100mH | .025 | 20 PITCH, 60 TEETH | .106 |
| 4.00 | 4.50 | 3.6 P-P | 250 | 280 | 100K | 100mH | .025 | 20 PITCH, 60 TEETH | .106 |
| 5.00 | 6.50 | 3.6 P-P | 250 | 280 | 100K | 100mH | .025 | 20 PITCH, 60 TEETH | .106 |
