TCA7
CE
New
Customized
Hammer
Paint Spray Gun
Any Color
OEM
Air Drill
Reciprocating Type
Impact wrench
Tunnel
Qianshao
Semi-automatic
Hand press
GM
Cartons or Others
CE
China
Product Description
Instruction
TCA-7 Pneumatic Pick has light-weight, simple structure, operate facility, auto stop when bump objective into pieces. It is suitable for drilling in mine, mining the soft ore; diging pole and feet-hole, karating water-ditch; or crashing concrete and clay in construction work; or working in the situation that need producing the impact in the mechanical industry such as assemble and unassemble the cincture pin in tractor, panzer and so on.
Specification
Exterior Dimension (L×W×H):456×160×110mm
Weigh:7.2kg
Rammar dia: 35mm
Rammar stroke:120mm
Rammar weigh:0.6kg
Work air pressure: 0.4~0.49Mpa
Impact energy(0.49Mpa): ≥30J
Impact frequency(0.49Mpa) :≥21.6Hz
Air consumption(0.49Mpa) :≤20L/S
Air pipe inner dia:19mm
Maintenance
Use And Notice
1. Machine should feed the rustproof oil before leave factory, it should dismantle for cleaning when use, reassembling copulate exterior should smear lubrication, and test run.
2. Make sure blow off the sundries within the pipe, when connecting air pipe.
3. Check carefully before aerate, if the air pipe route and connector was damage, each connect parts was reliable and safe.
Pneumatic Pick Operation
1-Ensure that drill positioned correctly.
2-Keep up your body balance and your feet leaving the drill.
3-Machine must tighten peak the crashing object,it need enough thrust to gain nice efficiency.
4-Abide local code and safety rules.
Air pipe and pressure
1-Air-pipe inner dia is 19mm,the length is ≤ 15m, the steel tube dia should be large enough between air compressor and pipe.
2-The air pressure is at 0.4~0.49Mpa. Air pressure is too high to destroy drill and spare parts and air pressure is too low to debase the work efficiency.
Lubrication
The principia to select lubrication is that the viscosity of the used oil should be high in high temperature locale; the viscosity of the used oil should be low in low temperature locale. See the list below to use the lubrication.
Malfunction and solution
TCA-7 Pneumatic Pick has light-weight, simple structure, operate facility, auto stop when bump objective into pieces. It is suitable for drilling in mine, mining the soft ore; diging pole and feet-hole, karating water-ditch; or crashing concrete and clay in construction work; or working in the situation that need producing the impact in the mechanical industry such as assemble and unassemble the cincture pin in tractor, panzer and so on.
Specification
Exterior Dimension (L×W×H):456×160×110mm
Weigh:7.2kg
Rammar dia: 35mm
Rammar stroke:120mm
Rammar weigh:0.6kg
Work air pressure: 0.4~0.49Mpa
Impact energy(0.49Mpa): ≥30J
Impact frequency(0.49Mpa) :≥21.6Hz
Air consumption(0.49Mpa) :≤20L/S
Air pipe inner dia:19mm
Maintenance
Use And Notice
1. Machine should feed the rustproof oil before leave factory, it should dismantle for cleaning when use, reassembling copulate exterior should smear lubrication, and test run.
2. Make sure blow off the sundries within the pipe, when connecting air pipe.
3. Check carefully before aerate, if the air pipe route and connector was damage, each connect parts was reliable and safe.
- Fill lubrication before opening machine, you should oil machine every two or three hours for use continuously.
- Don't use low-fire point and easy to pyrophoric lubricating oil, when use in the locale which has the super gas.
- Operating, should pay attention to interrupting the drill suddenly.
- The machine that use continuously should maintain termly, clean the dirty within machine, replace the mar and invalidation parts, eliminate accident hidden trouble.
Pneumatic Pick Operation
1-Ensure that drill positioned correctly.
2-Keep up your body balance and your feet leaving the drill.
3-Machine must tighten peak the crashing object,it need enough thrust to gain nice efficiency.
4-Abide local code and safety rules.
Air pipe and pressure
1-Air-pipe inner dia is 19mm,the length is ≤ 15m, the steel tube dia should be large enough between air compressor and pipe.
2-The air pressure is at 0.4~0.49Mpa. Air pressure is too high to destroy drill and spare parts and air pressure is too low to debase the work efficiency.
Lubrication
The principia to select lubrication is that the viscosity of the used oil should be high in high temperature locale; the viscosity of the used oil should be low in low temperature locale. See the list below to use the lubrication.
| Ambient temperature | Name | No |
| 10~30ºC | Machine oil | N46 |
| -10~10ºC | Machine oil | N22 |
| -30~-10ºC | Refrigerator oil | HD-13 |
| Malfunction | Cause | Solution |
| Efficiency droop | Low air pressure | If air consumption too large, reduce machine number. |
| Reduce pipe leak | ||
| If pipe is too long,cut short | ||
| Bad lubricate | Do use standard oil | |
| Water intake | Water pressure is higher than air pressure damage lubrication. Lower water pressure immediately. | |
| Mostly parts out of use | Change parts at once | |
| Machine out of work | Too much lubrication | According to prescribe change lubrication |
| Water intake | Lower water pressure immediately |
